![]() |
#1 |
Wizard
![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() Posts: 3,442
Karma: 300001
Join Date: Sep 2006
Location: Belgium
Device: PRS-500/505/700, Kindle, Cybook Gen3, Words Gear
|
Kindle boot log
![]() Code:
U-Boot 1.1.2 (Oct 29 2007 - 16:35:25) *** Welcome to Kindle *** U-Boot code: A3F00000 -> A3F3FA6C BSS: -> A3F77850 REV2 Bootloader: Kindle 400 MHz REV2 Board, Revision #9 Boot block version: 20070525 Checksum: 0x9F132881 Buildrev: 292-Kindle-012138 IOC Firmware Version #63 RAM Configuration: Bank #0: 0xA0000000 64 MB Flash Configuration: Bank #0: 0x00000000 128 MB Bank #1: 0x04000000 128 MB NAND Configuration: 256 MB BML_Init success BML_Open success **************** device info ******************* nPgsPerBlk = 64 nSctsPerPg = 4 nNumOfUsBlks = 2002 ************************************************* bml open success pi->nNumOfPartEntry: 10Success loading partition load env done op_amp#=65535 gain#=0 rve#=1015 panel#=010_01_23 panel#=010_01_23 serial#=B001BAB074xxxxxxx usb_force_sleep: hw_flags.disable_pdc_suspend = 0 waiting for CLKREADY Mode reg = 0x00000000 soft resetting device controller power switch is on Update battery level: >3720mV Boot battery level: >3680mV Alert battery level: >3600mV Current battery level: 3911mV (bootable) Loading partition "Standard Kernel" into 0xA2000000... Success Loading partition "Standard Initrd" into 0xA2E20000... Success iminfo a2000000 a2e20000 ## Checking Image at a2000000 ... Image Name: Linux-2.6.10-lab126 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1236608 Bytes = 1.2 MB Load Address: a0008000 Entry Point: a0008000 Verifying Checksum ... OK ## Checking Image at a2e20000 ... Image Name: initrd_fs.gz Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 689536 Bytes = 673.4 KB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK bootm a2000000 a2e20000 ## Booting image at a2000000 ... Image Name: Linux-2.6.10-lab126 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1236608 Bytes = 1.2 MB Load Address: a0008000 Entry Point: a0008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at a2e20000 ... Image Name: initrd_fs.gz Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 689536 Bytes = 673.4 KB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux................................................................................ done, booting the kernel. Linux version 2.6.10-lab126 (build@lab126-build) (gcc version 3.4.2) #1 Mon Oct 29 16:38:09 PST 2007 CPU: XScale-PXA255 [69052d06] revision 6 (ARMv5TE) CPU: D VIVT undefined 5 cache CPU: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets CPU: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets Machine: Fiona Platform Fiona Board Resistance : 150 mOhms Memory policy: ECC disabled, Data cache writeback Memory clock: 99.53MHz (*27) Run Mode clock: 398.13MHz (*4) Turbo Mode clock: 398.13MHz (*1.0, inactive) Built 1 zonelists Kernel command line: console=ttyS2,115200n8 root=/dev/rd/0 initrd=/linuxrc rw reboot=hard reserved 4096 bytes at a3fff000 for boot globals reserved 122880 bytes at a3fe1000 for framebuffer PID hash table entries: 512 (order: 9, 8192 bytes) Console: colour dummy device 80x30 Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 64MB = 64MB total Memory: 61456KB available (2070K code, 357K data, 100K init) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: Testing write buffer coherency: ok checking if image is initramfs...it isn't (no cpio magic); looks like an initrd Freeing initrd memory: 673K NET: Registered protocol family 16 Recalculated watermarks: wan: 3603 (was 3603) low: 3586 (was 3586) critical: 3536 (was 3536) REV2 board detected Power transition failed err=-5 for pnlcd video display class SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub PXA CPU frequency change support initialized NetWinder Floating Point Emulator V0.97 (extended precision) FPOW: Fiona Power Management Driver v0.54 squashfs: version 3.0 (2006/03/15) Phillip Lougher devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x1 Initializing Cryptographic API WATER: Disabling IOC voltage reporting, initing our own timer... Battery Voltage: 3881 mVolts (raw: 3854 mVolts) V[1] : ~3881~ A[1] : ~181~ T[1] : ~26~ OP Amp Offset : Uninitialized Op Amp Gain Correction : Uninitialized Voltage Reference Correction Factor : 1015 / 1000 IOC: Fiona IOC Driver v1.0, IOC FW version #63 Battery: 3.911 Volts, 26 Degrees C, 164 mA Draw, DISCHARGING, 72% PNLCD: Fiona PNLCD Driver v0.94 KEYBOARD: Fiona Keyboard Driver v1.0 ppoke driver: Major: 207 Rev. 4 Kernel v.2.6.10-lab126 /proc/peek initialized. /proc/poke initialized. ttyS0 at MMIO 0x40100000 (irq = 15) is a FFUART ttyS1 at MMIO 0x41600000 (irq = 0) is a HWUART ttyS2 at MMIO 0x40700000 (irq = 13) is a STUART io scheduler noop registered RAMDISK driver initialized: 8 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) PPP generic driver version 2.4.2 wan: AnyDATA DTEV WAN module driver 0.8.4 i2c /dev entries driver i2c_adapter i2c-0: found device 0x1a Advanced Linux Sound Architecture Driver Version 1.0.6 (Sun Aug 15 07:17:53 2004 UTC). soc: version 0.7 liam.girdwood@wolfsonmicro.com wm8971: WM8971 audio codec 0.2.3 soc: WM8971 <-> pxa2xx-i2s mapping ok ALSA device list: #0: WM8971 Portable Codec (SoC) NET: Registered protocol family 2 IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 4096 bind 8192) NET: Registered protocol family 1 NET: Registered protocol family 17 RAMDISK: Compressed image found at block 0 VFS: Mounted root (ext2 filesystem). Mounted devfs on /dev starting initrd... eink_fb: /dev/fb/0 frame buffer device, using 471K for video memory eink_fb: Apollo Display Driver 1.00 xsr: module license 'Samsung Proprietary' taints kernel. Samsung XSR Core 1.2.1-lab126-2 elevator: using noop as default io scheduler Samsung STL 1.2.1-lab126-2 Samsung RFS 1.2.1-lab126-2 kjournald starting. Commit interval 5 seconds EXT3 FS on stl8, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. starting init... dosfsck 2.11-lab126 (7 Dec 2006) dosfsck 2.11-lab126, 7 Dec 2006, FAT32, LFN Checking we can access the last sector of the filesystem Boot sector contents: System ID "mkdosfs" Media byte 0xf8 (hard disk) 512 bytes per logical sector 2048 bytes per cluster 32 reserved sectors First FAT starts at byte 16384 (sector 32) 2 FATs, 32 bit entries 386048 bytes per FAT (= 754 sectors) Root directory start at cluster 2 (arbitrary size) Data area starts at byte 788480 (sector 1540) 96416 data clusters (197459968 bytes) 8 sectors/track, 1 heads 0 hidden sectors 387204 sectors total Checking for unused clusters. Checking free cluster summary. /dev/stl0/9: 293 files, 7117/96416 clusters mount: Mounting /dev/mmc/blk0/part1 on /mnt/mmc failed: No such file or directory system: processing module dependencies system: loading module pdc pdc: version 1.0 pdc: IRQ 26 system: loading module usbserial drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic usbcore: registered new driver usbserial_generic usbcore: registered new driver usbserial drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0 system: initializing eInk driver for rootfs use eink_fb: /dev/fb/0 frame buffer device, using 588K for video memory eink_fb: Apollo Display Driver 1.00 eink_fb: write_eink_which, size=50327 eink_fb: curr_count=0 write_size=50327 eink_fb: done, status=1 1+0 records in 1+0 records out system: initializing random number generator system: initializing USB gadget driver g_file_storage gadget: controller 'pdc' not recognized g_file_storage gadget: File-backed Storage Gadget, version: 28 July 2004 g_file_storage gadget: Number of LUNs=2 system: initializing audio configuration for REV2 or higher system: initializing audio driver defaults system: initializing network configuration system: setting "conservative" processor power mode system: starting processor watchdog SA1100/PXA2xx Watchdog Timer: timer margin 60 sec watchdogd 0.1 Copyright (C) 2007 Lab126, Inc. All rights reserved. system: starting network connection watchdog netwatchd 0.5 Copyright (C) 2007 Lab126, Inc. All rights reserved. system: starting CVM memory watchdog nomkd 0.7 Copyright (C) 2006-2007 Lab126, Inc. All rights reserved. system: starting TPH monitor system: starting tphserver tphserver 0.2 Copyright (C) 2007 Lab126, Inc. All rights reserved. system: starting booklet framework Welcome to Kindle! kindle login: |
![]() |
![]() |
![]() |
#2 | |
Sir Penguin of Edinburgh
![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() Posts: 12,375
Karma: 23555235
Join Date: Apr 2007
Location: DC Metro area
Device: Shake a stick plus 1
|
Quote:
|
|
![]() |
![]() |
Advert | |
|
![]() |
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Opus cannot boot, stuck on boot screen | baloma | Bookeen | 35 | 11-13-2010 04:20 AM |
Connect Kindle 1 with TTL, can't boot.pls Help | michaelyzy | Kindle Developer's Corner | 0 | 05-12-2010 02:25 AM |
kindle dx cannot boot!! pls help me | chinaet | Amazon Kindle | 3 | 07-19-2009 08:23 PM |
New Member Log In | rcota@ec.rr.com | Introduce Yourself | 3 | 05-03-2008 10:46 AM |
Kindle boot logs | Nate the great | Kindle Developer's Corner | 10 | 11-27-2007 09:56 AM |