K5 Help With Final Steps of USBNet Hack

krebera · 08-05-2022, 08:03 PM

Hi, all!
Just trying to finalize getting UBNet running for the first time on my Kindle Touch (K5). I'm on OSX and the firmware on the Kindle is 5.3.7.3. I've installed the pertinent jailbreak and hot fix, as well as kterm, KUAL, and the package installer without issue. I'm thinking my problem here is probably sysadmin inexperience. I'll post my steps below in case I'm doing something glaringly wrong. Any input is appreciated!

1. Delete usbnet folder
2. Drop uninstall usbnet binary into mrpackages → Eject Kindle
3. Helper → Install MR Packages → USBNet uninstall
4. Re-Mount kindle → Re-install USBNet (
Code:
```
0.22.N I K5
```
)
5. Re-Mount kindle → Ensure config is set to defaults (IP addr of `192.168.15.244`)
6. Eject Kindle (unplug) → run
Code:
```
;un
```
→ plug back in
7. Network Settings showing “RNDIS/Ethernet Gadget”
8. Set “Configure IPV4” to “Manually” and set to
Code:
```
192.168.15.244
```
a. Subnet Mask and Router are blank here…
b. Status says “Connected” and I am seeing a green light
9. When I run
Code:
```
ssh root@192.168.15.244
```
nothing happens
10. Plugging and unplugging it while running
Code:
```
ifconfig
```
shows me that it’s showing up as
Code:
```
en8
```
11. I run sudo
Code:
```
ifconfig en8 192.168.15.244
```
12. Running
Code:
```
ssh root@192.168.15.244
```
now results in a “Port 22: Connection refused”
13. I generate an ssh key per the README thread and copy it over while the kindle is in mass storage mode
a. Place the
Code:
```
.pub
```
into
Code:
```
usbnet/etc
```
as
Code:
```
authorized_keys
```
14. Eject → Unplug →
Code:
```
;un
```
→ Plug back in → Re-do
Code:
```
ifconfig
```
15. Attempt ssh connect passing identity with corresponding id file
16. Still getting “Port 22: Connection Refused”

Anything here look weird? Again, anything helps! Thank you for your time

shamanNS · 08-05-2022, 08:23 PM

There are 2 ends of that USB cable, and those should have 2 different IP addresses?

Set a IP address for that RNDIS/Ethernet Gadget network device to something that is NOT 192.168.15.244 but is in the same subnet as that address, like say 192.168.15.5. Then ssh@192.168.15.244

krebera · 08-06-2022, 04:43 PM

Yo, thank you! It worked great lol. It also happens to make perfect sense haha. Thanks so much!

08-05-2022, 08:03 PM	#1
krebera Junior Member Posts: 2 Karma: 10 Join Date: Aug 2022 Device: Kindle Touch (K5)	Help With Final Steps of USBNet Hack Hi, all! Just trying to finalize getting UBNet running for the first time on my Kindle Touch (K5). I'm on OSX and the firmware on the Kindle is 5.3.7.3. I've installed the pertinent jailbreak and hot fix, as well as kterm, KUAL, and the package installer without issue. I'm thinking my problem here is probably sysadmin inexperience. I'll post my steps below in case I'm doing something glaringly wrong. Any input is appreciated! 1. Delete usbnet folder 2. Drop uninstall usbnet binary into mrpackages → Eject Kindle 3. Helper → Install MR Packages → USBNet uninstall 4. Re-Mount kindle → Re-install USBNet ( Code: 0.22.N I K5 ) 5. Re-Mount kindle → Ensure config is set to defaults (IP addr of `192.168.15.244`) 6. Eject Kindle (unplug) → run Code: ;un → plug back in 7. Network Settings showing “RNDIS/Ethernet Gadget” 8. Set “Configure IPV4” to “Manually” and set to Code: 192.168.15.244 a. Subnet Mask and Router are blank here… b. Status says “Connected” and I am seeing a green light 9. When I run Code: ssh root@192.168.15.244 nothing happens 10. Plugging and unplugging it while running Code: ifconfig shows me that it’s showing up as Code: en8 11. I run sudo Code: ifconfig en8 192.168.15.244 12. Running Code: ssh root@192.168.15.244 now results in a “Port 22: Connection refused” 13. I generate an ssh key per the README thread and copy it over while the kindle is in mass storage mode a. Place the Code: .pub into Code: usbnet/etc as Code: authorized_keys 14. Eject → Unplug → Code: ;un → Plug back in → Re-do Code: ifconfig 15. Attempt ssh connect passing identity with corresponding id file 16. Still getting “Port 22: Connection Refused” Anything here look weird? Again, anything helps! Thank you for your time

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
please help with final steps	Konakathie	Devices	14	05-25-2013 11:40 PM
Paid Hack Request: Photo Slideshow Hack for Kindle 3	chmreader	Kindle Developer's Corner	0	05-25-2011 02:24 PM
Book titles hack? Time delay hack?	re838uk	Sony Reader	0	10-08-2009 06:29 AM
Hack Attack! Esquire wants us to hack their e-paper cover	TadW	News	26	10-22-2008 04:51 AM

08-05-2022, 08:23 PM	#2
shamanNS Guru Posts: 995 Karma: 11500000 Join Date: Feb 2010 Location: Serbia Device: Kindle PW5, Kobo Libra 2, Kindle PW1	There are 2 ends of that USB cable, and those should have 2 different IP addresses? Set a IP address for that RNDIS/Ethernet Gadget network device to something that is NOT 192.168.15.244 but is in the same subnet as that address, like say 192.168.15.5. Then ssh@192.168.15.244

08-06-2022, 04:43 PM	#3
krebera Junior Member Posts: 2 Karma: 10 Join Date: Aug 2022 Device: Kindle Touch (K5)	Yo, thank you! It worked great lol. It also happens to make perfect sense haha. Thanks so much!

Advert