11-24-2020, 03:08 AM | #1 |
Groupie
Posts: 169
Karma: 43000
Join Date: Mar 2010
Device: none
|
Are there power charger spec limits?
I've recently gotten a power outlet USB charger adapter that is 5V/3A.
I know the T2 came with a 5V/1A adapter. Does the extra amperage pose a danger or does the reader only draw what it needs? I've seen different explanations on the net with regard to different devices, but it would be nice to be sure. |
11-24-2020, 07:07 AM | #2 |
Resident Curmudgeon
Posts: 76,101
Karma: 134368292
Join Date: Nov 2006
Location: Roslindale, Massachusetts
Device: Kobo Libra 2, Kobo Aura H2O, PRS-650, PRS-T1, nook STR, PW3
|
5V/3A will work no problem with your T2.
|
Advert | |
|
11-24-2020, 11:48 AM | #3 |
Running with scissors
Posts: 1,557
Karma: 14325282
Join Date: Nov 2019
Device: none
|
I asked this question on an electronics forum on reddit and the answer was that only the voltage matters. The higher amps mean that the device can use more of the electricity (meaning charge more quickly), if it's capable of it, but it's not a problem.
|
11-24-2020, 05:19 PM | #4 |
Groupie
Posts: 169
Karma: 43000
Join Date: Mar 2010
Device: none
|
Years ago I had someone at Radio Shack (if you remember those) tell me the opposite. That an adapter's amperage was more important than voltage. For example a device that runs on 8 D-batteries, which should be 12V can run just fine on 10V if the amperage is high enough. Maybe lower voltage is fine since batteries lose voltage over time, but higher is dangerous?
What is troubling is that the adapter has a list something like this: 5V : 3A 7.5V : 2A 15V : 1A From a wattage standpoint that makes sense since Power (Watts) = Voltage x Current. But does that mean a reader drawing 1A is getting 15V? That seems like an issue. |
11-24-2020, 05:47 PM | #5 | |
cosiñeiro
Posts: 1,319
Karma: 2200073
Join Date: Apr 2014
Device: BQ Cervantes 4
|
Quote:
More voltage might kill your device (allowed voltages are usually from 4.x to 5.x but better safe than sorry) More current won't kill your device because it is your device the one that draws current. If the adapter comes with a knob to change voltage then it is regulable by the user and will use the voltage you setup. If not and it is a "normal" mains to usb adapter you'll get 5v (up to 3A) unless the power circuit of the device you're going to charge negotiates for more voltage. In all the cases the specs of your charger is: xV (up to yA) and the one that decides the amperage is your device, not your charger. Sorry about my english |
|
Advert | |
|
12-04-2020, 05:28 AM | #6 |
Fanatic
Posts: 563
Karma: 403106
Join Date: Aug 2014
Device: PRS-T1
|
No charger is ever 5V, high amperage ones can easily go over 26V.
I think Sony series is 5V/500mA. While no device ever lets the charger charge directly the batteries (thus a misnomer ), for safety reasons, using a much much higher amperage charger would destroy the electronics in the Sony if it's not provided with safety measures against higher voltages. |
12-04-2020, 08:06 PM | #7 |
Groupie
Posts: 169
Karma: 43000
Join Date: Mar 2010
Device: none
|
Tested this for the first time yesterday. The charge icon came up, but when I returned the unit had not charges and I got a pop-up saying that.
I didn't have time to see if it was a cable issue or what, so I just plugged directly into my PC and charged off the port. I'll try again later, but I wonder if the T2 stopped the charge to protect itself. |
12-04-2020, 10:33 PM | #8 |
Wizard
Posts: 3,009
Karma: 18765431
Join Date: Oct 2010
Location: Sudbury, ON, Canada
Device: PRS-505, PB 902, PRS-T1, PB 623, PB 840, PB 633
|
A trick I used with my PRS-505 when it was dead was to charge it a few hours, unplug it and then power it up. Once it had booted, I would plug it in to charge fully. For safety, the current to a powered down device is very low. It takes a long time to charge in that state. Booting it up allows the hardware to negotiate a higher current during charging, speeding up the process.
|
12-05-2020, 12:45 AM | #9 |
Groupie
Posts: 169
Karma: 43000
Join Date: Mar 2010
Device: none
|
The PRS-T1 & 2 readers boot up when you connect power to them.
|
12-05-2020, 12:02 PM | #10 |
Wizard
Posts: 3,009
Karma: 18765431
Join Date: Oct 2010
Location: Sudbury, ON, Canada
Device: PRS-505, PB 902, PRS-T1, PB 623, PB 840, PB 633
|
I was talking about the situation where the battery has no charge and can't even boot the device. If yours can boot up but does not hold a charge, then the battery probably needs to be replaced.
|
12-07-2020, 12:03 PM | #11 | |
Fanatic
Posts: 563
Karma: 403106
Join Date: Aug 2014
Device: PRS-T1
|
Quote:
These are very picky units. I have a few Sony cellphones and all three T series, and I don't remember which charger is which and mixed up with others, cables and chargers, Samsung, Nokia, Panasonic, nonames etc. Some work, some don't. Some can only charge, some do both. I think the "true" 3A chargers have a recognition resistor (it's in the device) so it knows that the device can accept 0.5, 1, 2, 2.1 or 3A. It may be that cheap chargers do not react to this and pump all the juice, raising the voltage if the device resists the amperage. Anyway, it's always better to charge with a lower amperage than with full, even if it takes longer. What are nights for? |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
USB Power Adapter iPhone 4S Charger ? | lovelygirl | Apple Devices | 17 | 07-14-2012 02:39 PM |
Very nice power/charger option | taming | Kobo Tablets | 23 | 11-29-2011 03:17 PM |
Accessories Kindle Power Charger / Adapter | 1Bookworm | Amazon Kindle | 14 | 11-22-2011 10:51 PM |
which power adaptor/charger should I use with 1150? | hapax legomenon | Fictionwise eBookwise | 10 | 10-17-2008 08:25 AM |
PSP USB Power Charger works for the Reader as well | vampmiller | Sony Reader | 11 | 09-13-2007 04:26 PM |