Libra 2 Reviving a bricked Libra 2

biGPlant · 06-16-2024, 11:52 PM

I tried setting up koreader on a Kobo Libra 2 but read the guide incorrectly. Just a disclaimer, the guide is probably fine I believe I just screwed up somewhere. I thought I needed to extract the zip file at koreader github's release page rather than the one-click method linked at the bottom of the tutorial. Of course it didn't follow the "update then restart" step so I knew I did something wrong.

Once I realized my mistake, I connected the Kobo to my PC and extracted the correct zip file to the device. I removed the prior extracted files from the device after extracting the correct files to kobo. I safely removed the kobo then saw the "update and restart" step occur. It froze on "Updating" for around 10 minutes, so I naively forced shutdown thinking something went wrong again. When turning it on again, I see a small flash on the screen and a blinking led on the edge of the device. I consistently see the same error connecting to my PC, and attempting a manual reset.

I bought it from a third party seller so I assume warranty is voided and I know it will be difficult to remove the SD card with the waterproofing it has.

Is there a fix that doesn't involve a teardown?

Renate · 09-26-2024, 01:28 AM

I don't know the processor on the Libra 2, but usually low-level loaders are your friend.
If you can make a full, raw backup you can recover from anything.
Of course, once you've killed it before backup you'll need to get stuff from either an update or a person with the current image.

06-16-2024, 11:52 PM	#1
biGPlant Junior Member Posts: 4 Karma: 10 Join Date: Jun 2024 Device: Kobo Libra 2	Reviving a bricked Libra 2 I tried setting up koreader on a Kobo Libra 2 but read the guide incorrectly. Just a disclaimer, the guide is probably fine I believe I just screwed up somewhere. I thought I needed to extract the zip file at koreader github's release page rather than the one-click method linked at the bottom of the tutorial. Of course it didn't follow the "update then restart" step so I knew I did something wrong. Once I realized my mistake, I connected the Kobo to my PC and extracted the correct zip file to the device. I removed the prior extracted files from the device *after* extracting the correct files to kobo. I safely removed the kobo then saw the "update and restart" step occur. It froze on "Updating" for around 10 minutes, so I naively forced shutdown thinking something went wrong again. When turning it on again, I see a small flash on the screen and a blinking led on the edge of the device. I consistently see the same error connecting to my PC, and attempting a manual reset. I bought it from a third party seller so I assume warranty is voided and I know it will be difficult to remove the SD card with the waterproofing it has. Is there a fix that doesn't involve a teardown?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Bricked Libra 2, any hope? White screen of death	justwannaread	Kobo Reader	4	02-24-2024 06:15 AM
I think I bricked my Libra 2. :( Help?	Lily7	Kobo Reader	4	01-05-2024 03:32 PM
Libra 2E bricked, any suggestions what to try?	ams	Kobo Reader	1	10-18-2023 10:39 PM
Libra 2 Think I've bricked my Libra 2	HarrisonMarchant	Kobo Reader	2	08-28-2023 06:05 PM
Libra Bricked my Libra by tinlering	shoelesshunter	Kobo Developer's Corner	2	07-27-2020 09:44 AM

09-26-2024, 01:28 AM	#2
Renate Onyx-maniac Posts: 3,118 Karma: 12439909 Join Date: Feb 2012 Device: Nook NST, Glow2, 3, 4, '21, Kobo Aura2, Poke3, Poke5, Go6	I don't know the processor on the Libra 2, but usually low-level loaders are your friend. If you can make a full, raw backup you can recover from anything. Of course, once you've killed it before backup you'll need to get stuff from either an update or a person with the current image.

Advert