Mini Odd components on mini PCB and serial link - Page 2

euphy · 03-10-2013, 11:33 AM

Three ports is gilding the lily. I wonder if the other two are connected to sub-systems, or if they can be enabled as other serial devices? Kevin, right, glad it worked - did you just tape the connectors in place? Katch, I don't see any reason why that BT board wouldn't work - the serial ports do supply 3.3v as well so it'd fit right in. I'm a bit confused about how pairing works with devices that don't have interfaces, but I guess it must work somehow cos all the cool kids are doing it. I think there'd be enough room too, that's only a thin board. Certainly on the mini, the inner plastic shell would need to be cut away, but I reckon the snap-on outer cover would be ok.

KevinShort · 03-10-2013, 01:34 PM

So far I've just placed the connectors into the port in such a way that they stay put by themselves as long as I don't bump them. I have no idea what the three ports are for, I still haven't been able to get anything from J1 or J2, but I really don't know anything about how serial ports work.

Katch · 03-14-2013, 05:56 PM

Quote:

Originally Posted by euphy

I'm a bit confused about how pairing works with devices that don't have interfaces,

A pass code is set in eeprom on the BT serial device (usually 0000 or 1234) - this can be changed by issuing AT commands.

When it powers up it is immediately visible to other BT devices - once paired you'll have a new com port appear in device manager and then you just connect a terminal application to it as normal.

Best bet would be to solder some fine wires to the serial port and the BT module and install a small switch in the back plastic on the Vcc line.

The module is small enough to completely fit inside the plastics.

roberto85 · 10-03-2013, 01:13 PM

@euphy: I think the D and Q numbers are the LEDs row and column numbers in the infrared display as these LEDs form the matrix of the lights and when we touch the screen the output on the corresponding LEDs associated with those co-ordinate decreases which helps to identify the touch point on the screen and to know more about the these numbers you should look at the datasheet of the device.

turn-key assembly

Hekto · 10-06-2013, 10:03 AM

Hi,

I (and several other pilots) are already using Bluetooth modules in Kobos to connect to NMEA-sources. As you see in the picture, the HC05 module fits in the casing. I added two switches for turning of BT and entering AT-mode. The module can be programmed directly in the Kobo using telnet.

Regards,
Pascal

hijackgmh · 10-17-2013, 04:04 PM

Hekto, I want to use my Kobo mini with an HC-05 BT module as a dedicated soaring instrument. I won't use the Kobo for anything else. In that case, do I need the BT on/off switch and/or the VCC switch on my installation?

Mike

10-03-2013, 01:13 PM	#19
roberto85 Junior Member Posts: 1 Karma: 10 Join Date: Oct 2013 Device: none	@euphy: I think the D and Q numbers are the LEDs row and column numbers in the infrared display as these LEDs form the matrix of the lights and when we touch the screen the output on the corresponding LEDs associated with those co-ordinate decreases which helps to identify the touch point on the screen and to know more about the these numbers you should look at the datasheet of the device. turn-key assembly Last edited by roberto85; 10-17-2013 at 01:28 PM.

10-06-2013, 10:03 AM	#20
Hekto Junior Member Posts: 3 Karma: 10 Join Date: Jul 2013 Device: Kobo Mini	Bluetooth on Kobo Hi, I (and several other pilots) are already using Bluetooth modules in Kobos to connect to NMEA-sources. As you see in the picture, the HC05 module fits in the casing. I added two switches for turning of BT and entering AT-mode. The module can be programmed directly in the Kobo using telnet. Regards, Pascal Attached Thumbnails

10-17-2013, 04:04 PM	#21
hijackgmh Junior Member Posts: 1 Karma: 10 Join Date: Oct 2013 Device: Kobo	HC-05 BT and Kobo Mini Hekto, I want to use my Kobo mini with an HC-05 BT module as a dedicated soaring instrument. I won't use the Kobo for anything else. In that case, do I need the BT on/off switch and/or the VCC switch on my installation? Mike

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Calibre extra unwanted carriage returns in PCB file conversion	gragradownunder	Conversion	0	05-12-2011 07:57 AM
iPad Components Cost As Little As $220	Sonist	Apple Devices	7	02-10-2010 10:03 PM
Selling my PC Components	CommanderROR	Lounge	0	07-19-2006 11:43 AM

03-10-2013, 11:33 AM	#16
euphy Junior Member Posts: 7 Karma: 142 Join Date: Jan 2013 Device: kobo mini	Three ports is gilding the lily. I wonder if the other two are connected to sub-systems, or if they can be enabled as other serial devices? Kevin, right, glad it worked - did you just tape the connectors in place? Katch, I don't see any reason why that BT board wouldn't work - the serial ports do supply 3.3v as well so it'd fit right in. I'm a bit confused about how pairing works with devices that don't have interfaces, but I guess it must work somehow cos all the cool kids are doing it. I think there'd be enough room too, that's only a thin board. Certainly on the mini, the inner plastic shell would need to be cut away, but I reckon the snap-on outer cover would be ok.

03-10-2013, 01:34 PM	#17
KevinShort Addict Posts: 348 Karma: 209937 Join Date: Jan 2012 Location: Virginia, US Device: Kobo Wifi, Kobo Glo	So far I've just placed the connectors into the port in such a way that they stay put by themselves as long as I don't bump them. I have no idea what the three ports are for, I still haven't been able to get anything from J1 or J2, but I really don't know anything about how serial ports work.

Advert

Advert