Tutorial LanguageBreak - Software Jailbreak for (probably) any Kindle <=

[mergen3107]

And what is your Kindle model?

[riothamus]

Originally Posted by mergen3107

Which software did you install?

I used the downgrader 2.0 from the quoted link. I've used it successfully before on a Oasis 2. I tried to downgrade from 5.16.2.1.1 to 5.13.7. The only software I installed after the JB was KUAL, renametobin, and downgrader.

I also had it registered on amazon prior to attempting the downgrade.

It's an Oasis 10th generation.

[mergen3107]

What is the full name of the firmware you used?
update_kindle_all_new_oasis_v2_5.13.7.bin ?

[riothamus]

Originally Posted by mergen3107

What is the full name of the firmware you used?
update_kindle_all_new_oasis_v2_5.13.7.bin ?

Yes, that is exactly the name of the firmware I used.

[mergen3107]

OK
That sounds weird though.
I can see a few possibilities:
1) You Oasis 3 had aged and its storage died during update.
2) Kindle didn't like some file modifications
3) Update file got corrupted somehow

[nick84]

Originally Posted by mergen3107

Also, are you sure you are not stuck in demo?
Can you enable Wi-Fi?

It was still in demo mode. Thx mate. Problem solved.

[riothamus]

Originally Posted by mergen3107

OK
That sounds weird though.
I can see a few possibilities:
1) You Oasis 3 had aged and its storage died during update.
2) Kindle didn't like some file modifications
3) Update file got corrupted somehow

Thanks for your thoughts.

With any of those possibilities, is there anything I can do? I've had it plugged into the mains since my first post and it still doesn't show fully charged when usually an Oasis would be by now. It was 50-60% when the freeze happened. A lot of suggestions I found online said to leave it charging for 24 hours and they try to force a restart again. So that's next. After that all I can think of is to let the battery discharge and then plug it in again.

When I plug into a PC I get the device detected ding but a drive doesn't show up and there's nothing to eject so I can't use any of the force restart or force reset through PC options.

[mergen3107]

Did you try the very long power button press?
I don’t remember exactly, around 40-50 seconds maybe

[riothamus]

Originally Posted by mergen3107

Did you try the very long power button press?
I don’t remember exactly, around 40-50 seconds maybe

Yes, I tried that several times both plugged in and not plugged in. The screen will brighten and the charging light will flash a few times and then the screen dims and light goes steady on and nothing else happens. Stays on the "will be restarted" screen.

[ZeibaQ]

Originally Posted by Rauliki

When you look back at my posts I had a lot of problems, where most important one was coping LangiageBreak catalog to root of Kindle. You need to copy only what is inside.
And when I jailbreaked my another PW4, my demo after pushing button for Chinese language didnt went to chinese at all. I had english all the time.
I would say instruction works different for different models.
If you dont know if you are in right place, sometimes restart will get you there.


About step 15 - I always have microusb cable ready just almost plugged to Kindle. And push just when the power off info is on screen. You have maybe 2-3 seconds window.

Thanks Rauliki for your reply..
I copied the content of languagebreak folder directly to the kindle, namely:
".active_content_sandbox
documents
jb
jb.html
patchedUks.sqsh"

and I made sure to copy and replace existing files in step 15, before ejecting the kindle.
then, I pushed the power button like in step 16. and some of the times , I didn't push it, but the kindle started any way..
and all the times, it didn't show the language selection screen

[freddie3957]

My Kindle keeps struggling with the sideloading. At step 19, there are no log messages on the screen, and I can't install any .bin files (both firmware files and update_hotfix_languagebreak, as I get a message about an invalid update file.
I'm using the PW 4 with version 5.16.21.

[mergen3107]

Well, yeah, this FW is not supported by LanguageBreak…

[JSWolf]

Originally Posted by freddie3957

My Kindle keeps struggling with the sideloading. At step 19, there are no log messages on the screen, and I can't install any .bin files (both firmware files and update_hotfix_languagebreak, as I get a message about an invalid update file.
I'm using the PW 4 with version 5.16.21.

You could not link to your image. You should attach your image to your post so it can be seen.