07-09-2024, 03:55 PM | #16 | |
Connoisseur
Posts: 52
Karma: 10
Join Date: Jan 2024
Device: Boox Note Air 3
|
Quote:
I found an abl_a partition. Does that help? I extracted it with: ./edl/edl r abl_a abl_a.prc File attached. Last edited by dcarvil; 07-09-2024 at 03:58 PM. |
|
07-09-2024, 03:58 PM | #17 |
Onyx-maniac
Posts: 3,176
Karma: 12537601
Join Date: Feb 2012
Device: Nook NST, Glow2, 3, 4, '21, Kobo Aura2, Poke3, Poke5, Go6
|
Well, then do it! But safely.
Code:
fastboot erase fishheads Erasing 'fishheads' (bootloader) Invalid partition name fishheads FAILED (remote: '') fastboot: error: Command failed fastboot flash fishheads anyfileyoulike Sending 'fishheads' (2583 KB) OKAY [ 0.073s] Writing 'fishheads' (bootloader) Invalid partition name fishheads FAILED (remote: '') fastboot: error: Command failed Now's a great time to learn all about EDL. Because you're going to need it! http://www.temblast.com/edl.htm I'm not sure if the NoteAir3 uses the sdm662.bin loader. Code:
adb reboot edl edl /lsdm662.bin eel /u /r /pabl_a abl_a.img edl /z |
07-09-2024, 04:01 PM | #18 |
Onyx-maniac
Posts: 3,176
Karma: 12537601
Join Date: Feb 2012
Device: Nook NST, Glow2, 3, 4, '21, Kobo Aura2, Poke3, Poke5, Go6
|
Our messages passed each other.
Wasn't it fortunate that I just finished writing my UEFI tool this morning? Now I can see at a glance that they chopped your abl off at the knees. abl supports the fastboot protocol when it's acting as bootloader. You can use EDL to flash your Magisk'ed boot image. Be careful and keep a copy of the original boot image. Nap time... zzz... Last edited by Renate; 07-09-2024 at 04:10 PM. |
07-09-2024, 04:05 PM | #19 | |
Connoisseur
Posts: 52
Karma: 10
Join Date: Jan 2024
Device: Boox Note Air 3
|
Quote:
Our messages crossed. The abl_a image is in my previous reply. I'm getting unknown command on both erase and flash. xfx:~/oldhome/Phone/boox/na2p $ fastboot devices 8863F9C3 fastboot xfx:~/oldhome/Phone/boox/na2p $ fastboot erase fisheads Erasing 'fisheads' FAILED (remote: 'unknown command') fastboot: error: Command failed xfx:~/oldhome/Phone/boox/na2p $ fastboot flash fisheads magisk_patched-26400_QLQZ1.img Warning: skip copying fisheads image avb footer (fisheads partition size: 0, fisheads image size: 100663296). Sending 'fisheads' (98304 KB) OKAY [ 2.242s] Writing 'fisheads' FAILED (remote: 'unknown command') fastboot: error: Command failed xfx:~/oldhome/Phone/boox/na2p $ |
|
07-09-2024, 04:20 PM | #20 | |
Connoisseur
Posts: 52
Karma: 10
Join Date: Jan 2024
Device: Boox Note Air 3
|
Quote:
|
|
07-30-2024, 07:56 AM | #21 | |
Junior Member
Posts: 7
Karma: 10
Join Date: Jan 2024
Device: Onyx Boox Page
|
Quote:
|
|
07-30-2024, 08:27 AM | #22 |
Onyx-maniac
Posts: 3,176
Karma: 12537601
Join Date: Feb 2012
Device: Nook NST, Glow2, 3, 4, '21, Kobo Aura2, Poke3, Poke5, Go6
|
There are basically three ways to flash something:
Fastboot flashing seems to be disappearing. You might try to retain the old abl from a previous update. Or just backup your current abl. Besides flashing there should not be incompatibility between the old and the new abl. |
07-31-2024, 03:13 AM | #23 |
Old Kaz
Posts: 208
Karma: 1064151
Join Date: May 2010
Device: PocketBook Era
|
Is there no update 3.5.3 for Poke 3?
|
07-31-2024, 07:12 AM | #24 |
Onyx-maniac
Posts: 3,176
Karma: 12537601
Join Date: Feb 2012
Device: Nook NST, Glow2, 3, 4, '21, Kobo Aura2, Poke3, Poke5, Go6
|
Apparently not.
The last update was ONYX/Poke3/Poke3:10/2023-12-12_23-45_3.5_4687b1901/12699:user/dev-keys At the bottom of this page it omits the Poke3. |
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Onyx boox M92 - recovery update | Andrewski | Onyx Boox | 0 | 11-11-2018 03:20 PM |
Onyx Boox M92 freeze and does not update | ingmecc | Onyx Boox | 2 | 12-13-2013 08:12 AM |
Onyx Boox M92: not booting after update | maxmin | Onyx Boox | 5 | 11-02-2012 07:25 AM |
Firmware update released for the Onyx Boox 60 | Nate the great | News | 12 | 01-05-2010 07:54 AM |
Onyx Boox update | Nate the great | News | 3 | 12-09-2009 03:34 PM |