One-Click Install Packages for KOReader & Plato

[Frenzie]

That release predates the new devices. http://build.koreader.rocks/download/nightly/

[DNSB]

Originally Posted by Andrew NZ

Hi there,

I am completely new to Kobo (Libre 2) but am trying to install the KOReader via my W11 PC using the installer at the beginning of this thread. I downloaded the 2024 KO Reader zip plus the installer file, unblocked the script and ran it with PowerShell, I saw the command prompt window open and immediately close and absolutely nothing else happened. My Kobo was connected at drive E at the time. Any suggestions?

I would suggest opening a Powershell window and then running the script from there so you can see the results. You did place the install.ps1 script and the .zip file in the same directory? You will need to use .\install.ps1 to execute the script from the Powershell window.

[DNSB]

Originally Posted by raildot

After deciding I might try installing them individually I discovered that Plato's GitHub had a new release last week with "support for Kobo Clara BW". Unfortunately the download it is not packaged in a way I can try it on my Kobo. Is it possible to update the zip file on this thread for Plato to reflect the new update?

1. download install.ps1 following the instructions to unblock it
2. download OCP-Plato-0.9.42_KOReader-v2024.04.zip and place it in the same directory as install.ps1. Do not unzip the archive.
3. open a Powershell window in that directory and run ./install.ps1
4. if all goes well, continue to update Plato and KOReader
5. download Plato-0.9.43.zip.
6. open it with a zip file utility.
7. copy the contents of the .zip file to the /.adds/plato directory on your Kobo.
8. download the latest KOReader nightly.
9. open it with a zip file utility
10. copy the contents of the .zip file to the /.adds/koreader directory on your Kobo.

All the heavy lifting should have been done by the install script.

[raildot]

Originally Posted by DNSB

1. download install.ps1 following the instructions to unblock it
2. download OCP-Plato-0.9.42_KOReader-v2024.04.zip and place it in the same directory as install.ps1. Do not unzip the archive.
3. open a Powershell window in that directory and run ./install.ps1
4. if all goes well, continue to update Plato and KOReader
5. download Plato-0.9.43.zip.
6. open it with a zip file utility.
7. copy the contents of the .zip file to the /.adds/plato directory on your Kobo.
8. download the latest KOReader nightly.
9. open it with a zip file utility
10. copy the contents of the .zip file to the /.adds/koreader directory on your Kobo.

All the heavy lifting should have been done by the install script.

Thank you, I appreciate your help. I factory reset and started the process again. I followed your instructions and Plato now works. KOReader still crashes my device however.

[hatuluang]

Originally Posted by raildot

Thank you, I appreciate your help. I factory reset and started the process again. I followed your instructions and Plato now works. KOReader still crashes my device however.

For KOReader, you need to use the latest koreader nightly update, download the one for Kobo, extract it, and copy the folder koreader and paste it on .adds folder on your Kobo to replace the initial koreader folder.

[raildot]

Originally Posted by hatuluang

For KOReader, you need to use the latest koreader nightly update, download the one for Kobo, extract it, and copy the folder koreader and paste it on .adds folder on your Kobo to replace the initial koreader folder.

This is the nightly file I used for my Kobo Clara BW that didn't work: koreader-kobo-v2024.04-221-g6d73442ec_2024-06-30.zip

I extracted it directly into the koreader folder in .adds

I could try the process again but I'm pretty sure that I used the correct version first time, no?

[hatuluang]

Originally Posted by raildot

This is the nightly file I used for my Kobo Clara BW that didn't work: koreader-kobo-v2024.04-221-g6d73442ec_2024-06-30.zip

I extracted it directly into the koreader folder in .adds

I could try the process again but I'm pretty sure that I used the correct version first time, no?

the latest one is 2024-07-03

You need to change/replace the initial koreader folder with koreader folder from nightly update.
The straightforward way is to copy koreader folder from nightly update and paste it on .adds folder, It will replace the koreader folder from the initial installation.