![]() |
#16 | |
Enthusiast
![]() Posts: 49
Karma: 10
Join Date: Jan 2024
Device: Boox Note Air 3
|
Quote:
I found an abl_a partition. Does that help? I extracted it with: ./edl/edl r abl_a abl_a.prc File attached. Last edited by dcarvil; 07-09-2024 at 02:58 PM. |
|
![]() |
![]() |
![]() |
#17 |
Wizard
![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() Posts: 2,860
Karma: 12000011
Join Date: Feb 2012
Device: Nook NST, Glow2, 3, 4, '21, Kobo Aura2, Poke3, Poke5
|
Well, then do it! But safely.
Code:
fastboot erase fishheads Erasing 'fishheads' (bootloader) Invalid partition name fishheads FAILED (remote: '') fastboot: error: Command failed fastboot flash fishheads anyfileyoulike Sending 'fishheads' (2583 KB) OKAY [ 0.073s] Writing 'fishheads' (bootloader) Invalid partition name fishheads FAILED (remote: '') fastboot: error: Command failed ![]() Now's a great time to learn all about EDL. Because you're going to need it! http://www.temblast.com/edl.htm I'm not sure if the NoteAir3 uses the sdm662.bin loader. Code:
adb reboot edl edl /lsdm662.bin eel /u /r /pabl_a abl_a.img edl /z |
![]() |
![]() |
![]() |
#18 |
Wizard
![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() Posts: 2,860
Karma: 12000011
Join Date: Feb 2012
Device: Nook NST, Glow2, 3, 4, '21, Kobo Aura2, Poke3, Poke5
|
Our messages passed each other.
Wasn't it fortunate that I just finished writing my UEFI tool this morning? Now I can see at a glance that they chopped your abl off at the knees. abl supports the fastboot protocol when it's acting as bootloader. You can use EDL to flash your Magisk'ed boot image. Be careful and keep a copy of the original boot image. Nap time... zzz... Last edited by Renate; 07-09-2024 at 03:10 PM. |
![]() |
![]() |
![]() |
#19 | |
Enthusiast
![]() Posts: 49
Karma: 10
Join Date: Jan 2024
Device: Boox Note Air 3
|
Quote:
Our messages crossed. The abl_a image is in my previous reply. I'm getting unknown command on both erase and flash. xfx:~/oldhome/Phone/boox/na2p $ fastboot devices 8863F9C3 fastboot xfx:~/oldhome/Phone/boox/na2p $ fastboot erase fisheads Erasing 'fisheads' FAILED (remote: 'unknown command') fastboot: error: Command failed xfx:~/oldhome/Phone/boox/na2p $ fastboot flash fisheads magisk_patched-26400_QLQZ1.img Warning: skip copying fisheads image avb footer (fisheads partition size: 0, fisheads image size: 100663296). Sending 'fisheads' (98304 KB) OKAY [ 2.242s] Writing 'fisheads' FAILED (remote: 'unknown command') fastboot: error: Command failed xfx:~/oldhome/Phone/boox/na2p $ |
|
![]() |
![]() |
![]() |
#20 | |
Enthusiast
![]() Posts: 49
Karma: 10
Join Date: Jan 2024
Device: Boox Note Air 3
|
Quote:
|
|
![]() |
![]() |
![]() |
#21 | |
Junior Member
![]() Posts: 7
Karma: 10
Join Date: Jan 2024
Device: Onyx Boox Page
|
Quote:
|
|
![]() |
![]() |
![]() |
#22 |
Wizard
![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() Posts: 2,860
Karma: 12000011
Join Date: Feb 2012
Device: Nook NST, Glow2, 3, 4, '21, Kobo Aura2, Poke3, Poke5
|
There are basically three ways to flash something:
Fastboot flashing seems to be disappearing. You might try to retain the old abl from a previous update. Or just backup your current abl. Besides flashing there should not be incompatibility between the old and the new abl. |
![]() |
![]() |
![]() |
#23 |
Old Kaz
![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() Posts: 208
Karma: 1064151
Join Date: May 2010
Device: PocketBook Era
|
Is there no update 3.5.3 for Poke 3?
|
![]() |
![]() |
![]() |
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Onyx boox M92 - recovery update | Andrewski | Onyx Boox | 0 | 11-11-2018 02:20 PM |
Onyx Boox M92 freeze and does not update | ingmecc | Onyx Boox | 2 | 12-13-2013 07:12 AM |
Onyx Boox M92: not booting after update | maxmin | Onyx Boox | 5 | 11-02-2012 06:25 AM |
Firmware update released for the Onyx Boox 60 | Nate the great | News | 12 | 01-05-2010 06:54 AM |
Onyx Boox update | Nate the great | News | 3 | 12-09-2009 02:34 PM |